How to Make a Fitted Diaper from an Old T-Shirt
Thanks for subscribing to our newsletter. You really can turn old t-shirts into fitted diapers. Learn how in this step-by-step tutorial!
Cloth diapers don’t need to cost a lot of money. If you have some basic sewing skills and your own sewing machine (or one you can borrow), you can make a fitted diaper from a couple of old t-shirts.
You might be surprised how absorbent t-shirts can be! I did some testing, and this t-shirt diaper is just as absorbent as a standard cotton prefold! I’ve created an easy tutorial with step-by-step instructions.

Fitted diapers are often made out of cotton or other absorbent
materials including bamboo and hemp. While most manufacturers use new
materials, the materials found in 100% cotton t-shirts are an more
affordable (and eco-friendly!) alternative!
Materials Needed to Make a Fitted Diaper:
- 2 pre-washed 100% cotton t-shirts (larger men’s sizes are preferable, look for t-shirts that are made of heavy fabric) – pre-loved are preferable!
- Coordinating polyester thread
- 1/4″ wide swimsuit elastic or other performance elastic (I buy mine from Wazoodle, but here’s a more complete list of great sources for diaper making supplies)
- Sewing machine with zigzag
- Optional: 1 piece of woven cotton fabric such as flannel for outside layer if you plan to use a snappi (since snappis sometimes snag knit fabrics) – make sure to pre-wash and dry this so it doesn’t shrink later!

Instructions to Make a Fitted Diaper from Old T-Shirts
Cut sleeves and necklines off of 2 old t-shirts and spread out. Trace your preferred cloth diaper onto the t-shirt, adding a 1/2″ seam allowance.

Using the diaper pattern, cut 3 layers from the t-shirts, avoiding any seams, which will wear unevenly and may be uncomfortable for your baby. I prefer to trace a diaper that I already have that fits my baby well,
but if you need cloth diaper patterns, check out some of the free patterns for cloth diapers here.

Optional:
If you are are adding a flannel or woven outer layer on your fitted diaper, cut it out now, with right side facing in, as shown below.

Note: you can’t see it, but there is a seam on my flannel print. If you have a large piece
of flannel, you won’t need this, but I chose to use a smaller piece of
flannel and piece it together. If you have a print that runs in a
single direction, you can ensure that the print is right way up on both
the front and the back of the diaper by sewing the fabric down the
middle, as shown.
Fitted diapers can take a long time to dry because they have so may layers of fabric all sewn together. My fitted diaper design uses a separate diaper soaker that lays on top of the fitted to provide extra absorbency, but it separates from the diaper to dry faster.
You can make your diaper soaker in any shape that you want, as long as it fits inside your finished diaper. I chose to model mine on a large insert. Using the sleeves of the t-shirt, plus the area left near the neckline, you should be able to get 4 to 5 layers for your insert. Cut this out with a 1/2″ seam allowance (my picture shows slightly more because the fabric wasn’t all straight!).

Sew around your insert, leaving one end open. Trim back to 1/4″ seam allowances, and turn right-side out.

Next, top-stitch your insert, taking care to close the open end. As you can see, I made a slight mistake here and forgot to make sure the label from the shirt was facing toward the center of the diaper. This won’t affect its functionality, and since the shirt was used, the label is just as soft as the t-shirt itself, so I’m not worried about it causing any discomfort!

If you would like a semi all-in-two design, you can leave the soaker unattached and lay it on top of your diaper. I prefer to attach it to the diaper at the back, so that I don’t have to search through the laundry to find the appropriate soaker. To attach it, you can either stitch it on, which is what I’m doing here, or you can add a snap (if you have a snap press or snap pliers). I recently purchased a set of KAM Snap Pliers, and they are very easy to use.
To attach the soaker, sew it to all 3 layers of the t-shirt diaper, but not the outer flannel layer.

If you have sewn your insert into the diaper, it is very important to be sure that it is laying facing up, with the flannel print facing down directly onto it. If it isn’t in this order, you will discover that the soaker will be inside the core of the diaper when you are done – meaning your diaper will take a long time to dry!
Using 1/2″ seam allowance, sew around diaper, leaving back open for
turning. I don’t have a serger, so these directions are for a turned and
top-stitched diaper.
Because we’ll be turning the diaper and
top-stitching around the outside to hold it all in place, it is best to
remove any unnecessary bulk around the seams. Trim edges to 1/4″ from
seam (or slightly less), and be sure to clip all corners on the diagonal
to remove excess fabric that would make it hard to get a nice corner
once it’s turned. NOTE: Do not trim where the back is still open –
it’s very hard to close the diaper up later if you don’t leave enough fabric to turn under!

Next, cut 2 pieces of swimwear elastic for the diaper legs, and one for the back. For this step, it’s usually best to follow the instructions on your diaper pattern, or measure the elastic in the diaper you are using as a guide. I made a size large fitted, and I used 6″ for the legs and 4 and 1/2″ for the back, but this will differ depending on the size of the diaper you are making.

Pulling snug, tack the elastic on either side of the opening at the back of the diaper. Stitch to the outside of the outer seam so that (later!) you can turn the diaper easily.

For each leg opening, sew the elastic in place according to your pattern. Be sure to stitch and back-stitch so that the elastic doesn’t com undone later. Sew to the fabric outside of the outer seam, so that you can turn the diaper.

Tack elastic at the opposite end of the diaper, pulling snug. I will not be stitching down the elastic, because this makes it much harder to replace elastic in a few years. If you invest in high quality swimsuit elastic, it will last much longer than the basic elastics available through Wal-Mart or regular craft stores!

Turn and top-stitch the diaper with a 1/8″ seam allowance, closing along back opening as you go. On this particular diaper, I stitched along the leg openings using a 3/8″ seam allowance and taking care not to catch the elastic in the stitching. Some diaper patterns suggest not stitching along the elastic at all, and I have tried both with success, so it’s your choice.

Your finished diaper should look something like this on the inside.

Many fitted diapers are now using a fold-down rise (called an FDR) to adjust the sizing. If you like, you can do the same with you diaper, similar to my photo below. Isn’t it cute?

I opted to make this diaper without any snaps or velcro. Because I used a flannel print, I can easily use a Snappi (or Boingos) to fasten it, as shown below.

Don’t forget, your fitted diaper will require a cover to make it waterproof. Click on the link for more information on cloth diaper covers, including some of our favorite brands.
Go to top of Make a Fitted Diaper from Old T-Shirts
For more do-it-yourself cloth diapering projects and tutorials, go back to Making Cloth Diapers.
At
Thinking About Cloth Diapers, we offer reliable, up-to-date cloth
diaper research to save you time so you can get on with the other things
you want to do.